X-Git-Url: http://git.sameswireless.fr/l2tpns.git/blobdiff_plain/3057f5e655405b7ba84a559213a1dbaaa3eaaab6..211cb9427c7f78f59928d7f850721e7d0dfbf271:/Docs/startup-config.5?ds=inline

diff --git a/Docs/startup-config.5 b/Docs/startup-config.5
index c1112ff..35d5346 100644
--- a/Docs/startup-config.5
+++ b/Docs/startup-config.5
@@ -2,7 +2,7 @@
 .de Id
 .ds Dt \\$4 \\$5
 ..
-.Id $Id: startup-config.5,v 1.2 2004-11-27 05:19:54 bodea Exp $
+.Id $Id: startup-config.5,v 1.7 2005-05-10 11:59:25 bodea Exp $
 .TH STARTUP-CONFIG 5 "\*(Dt" L2TPNS "File Formats and Conventions"
 .SH NAME
 startup\-config \- configuration file for l2tpns
@@ -51,6 +51,11 @@ is any one of the syslog logging facilities, such as
 If set, the process id will be written to the specified file.  The
 value must be an absolute path.
 .TP
+.B random_device
+Path to random data source (default
+.BR /dev/urandom ).
+Use "" to use the rand() library function.
+.TP
 .B l2tp_secret
 The secret used by
 .B l2tpns
@@ -63,14 +68,6 @@ Whenever a PPP connection is established, DNS servers will be sent to the
 user, both a primary and a secondary.  If either is set to 0.0.0.0, then that
 one will not be sent.
 .TP
-.B save_state
-When
-.B l2tpns
-receives a STGTERM it will write out its current ip_address_pool,
-session and tunnel tables to disk prior to exiting to be re-loaded at
-startup.  The validity of this data is obviously quite short and the
-intent is to allow an sessions to be retained over a software upgrade.
-.TP
 .BR primary_radius , " secondary_radius"
 Sets the RADIUS servers used for both authentication and accounting. 
 If the primary server does not respond, then the secondary RADIUS
@@ -90,9 +87,22 @@ and a
 .B Stop
 record when the session is closed.
 .TP
+.B radius_interim
+If
+.B radius_accounting
+is on, defines the interval between sending of RADIUS interim
+accounting records (in seconds).  Note: checking of this interval
+occurs no more frequently than
+.B cleanup_interval
+seconds (see below).
+.TP
 .B radius_secret
 Secret to be used in RADIUS packets.
 .TP
+.B radius_authtypes
+A comma separated list of supported RADIUS authentication methods
+("pap" or "chap"), in order of preference (default "pap").
+.TP
 .B bind_address
 When the tun interface is created, it is assigned the address
 specified here.  If no address is given, 1.1.1.1 is used.  Packets
@@ -105,7 +115,7 @@ Address to send to clients as the default gateway.
 .B send_garp
 Determines whether or not to send a gratuitous ARP for the
 .B bind_address
-when the server is ready to handle traffic (default:  true).  This
+when the server is ready to handle traffic (default: true).  This
 setting is ignored if BGP is configured.
 .TP
 .B throttle_speed
@@ -127,8 +137,7 @@ doesn't work properly.
 If set to true, then the current bandwidth utilization will be logged
 every second.  Even if this is disabled, you can see this information
 by running the
-.B
-uptime
+.B uptime
 command on the CLI.
 .TP
 .B cleanup_interval
@@ -160,6 +169,12 @@ process in memory.
 .B icmp_rate
 Maximum number of host unreachable ICMP packets to send per second.
 .TP
+.B packet_limit
+Maximum number of packets of downstream traffic to be handled each
+tenth of a second per session.  If zero, no limit is applied (default: 
+0).  Intended as a DoS prevention mechanism and not a general
+throttling control (packets are dropped, not queued).
+.TP
 .B cluster_address
 Multicast cluster address (default: 239.192.13.13).
 .TP
@@ -173,6 +188,11 @@ Interval in tenths of a second between cluster heartbeat/pings.
 Cluster heartbeat timeout in tenths of a second.  A new master will be
 elected when this interval has been passed without seeing a heartbeat
 from the master.
+.TP
+.B ipv6_prefix
+Enable negotiation of IPv6.  This forms the the first 64 bits of the
+client allocated address.  The remaining 64 come from the allocated
+IPv4 address and 4 bytes of 0s.
 .RE
 .SS BGP ROUTING
 The routing configuration section is entered by the command
@@ -275,11 +295,8 @@ and
 .I dest
 are as described above for standard lists.
 .PP
-For
-.B tcp
-and
-.B udp
-matches, source and destination may be optionally followed by a
+For TCP and UDP matches, source and destination may be optionally
+followed by a
 .I ports
 specification:
 .IP
@@ -290,20 +307,33 @@ specification:
 range
 .I from to
 .PP
-.B tcp
-matches may also specify
 .I flags
-to match against tcp header flags:
-.IP
+may be one of:
+.RS
+.HP
 .RB { match\-any | match\-all }
 .RB { + | - }{ fin | syn | rst | psh | ack | urg }
 \&...
 .br
+Match packets with any or all of the tcp flags set
+.RB ( + )
+or clear
+.RB ( - ).
+.HP
 .B established
-.PP
-.RB ' established '
-is shorthand for
-.RB ' "match-any +ack +rst -syn" '.
+.br
+Match "established" TCP connections:  packets with
+.B RST
+or
+.B ACK
+set, and
+.B SYN
+clear.
+.HP
+.B fragments
+.br
+Match IP fragments.  May not be specified on rules with layer 4
+matches.
 .RE
 .SH SEE ALSO
 .BR l2tpns (8)