X-Git-Url: http://git.sameswireless.fr/l2tpns.git/blobdiff_plain/4d7677820087558df4836c006509903fa0f6d83b..404aee88c9ed9281cb167dcb4b19fe212b943a88:/Docs/manual.html

diff --git a/Docs/manual.html b/Docs/manual.html
index 8dd2532..ad4bbec 100644
--- a/Docs/manual.html
+++ b/Docs/manual.html
@@ -191,14 +191,6 @@ user, both a primary and a secondary.  If either is set to 0.0.0.0, then that
 one will not be sent.
 </LI>
 
-<LI><B>save_state</B> (boolean)<BR>
-When l2tpns receives a STGTERM it will write out its current
-ip_address_pool, session and tunnel tables to disk prior to exiting to
-be re-loaded at startup.  The validity of this data is obviously quite
-short and the intent is to allow an sessions to be retained over a
-software upgrade.
-</LI>
-
 <LI><B>primary_radius</B> (ip address)
 <LI><B>secondary_radius</B> (ip address)<BR>
 Sets the RADIUS servers used for both authentication and accounting. 
@@ -231,6 +223,17 @@ This secret will be used in all RADIUS queries.  If this is not set then
 RADIUS queries will fail.
 </LI>
 
+<LI><B>radius_authtypes</B> (string)</BR>
+A comma separated list of supported RADIUS authentication methods
+(<B>pap</B> or <B>chap</B>), in order of preference (default <B>pap</B>).
+</LI>
+
+<LI><B>allow_duplicate_users</B> (boolean)</BR>
+Allow multiple logins with the same username.  If false (the default),
+any prior session with the same username will be dropped when a new
+session is established.
+</LI>
+
 <LI><B>bind_address</B> (ip address)<BR>
 When the tun interface is created, it is assigned the address
 specified here.  If no address is given, 1.1.1.1 is used.  Packets
@@ -332,6 +335,11 @@ Cluster heartbeat timeout in tenths of a second.  A new master will be
 elected when this interval has been passed without seeing a heartbeat
 from the master.
 </LI>
+
+<LI><B>cluster_master_min_adv</B> (int)<BR>
+Determines the minumum number of up to date slaves required before the
+master will drop routes (default: 1).
+</LI>
 </UL>
 
 <P>BGP routing configuration is entered by the command:
@@ -692,14 +700,10 @@ killall -HUP l2tpns
 
 The signals understood are:
 <UL>
-<LI>SIGHUP - Reload the config from disk and re-open log file<P></LI>
-<LI>SIGTERM / SIGINT - Shut down for a restart.  This will dump the current
-state to disk (if <EM>save_state</EM> is set to true).  Upon restart, the
-process will read this saved state to resume active sessions.<P>
+<LI>SIGHUP - Reload the config from disk and re-open log file</LI>
+<LI>SIGTERM / SIGINT - Shut down.</LI>
 <LI>SIGQUIT - Shut down cleanly.  This will send a disconnect message for
-every active session and tunnel before shutting down.  This is a good idea
-when upgrading the code, as no sessions will be left with the remote end
-thinking they are open.</LI>
+every active session and tunnel before shutting down.</LI>
 </UL>
 
 <H2 ID="Throttling">Throttling</H2>