Following development LAC functionality

[l2tpns.git] / Docs / manual.html

diff --git a/Docs/manual.html b/Docs/manual.html
index 65d7f4c..f52ad29 100644 (file)
--- a/Docs/manual.html
+++ b/Docs/manual.html
@@ -56,7 +56,6 @@ H3 {
     <LI><A HREF="#Filtering">Filtering</A></LI>
     <LI><A HREF="#Clustering">Clustering</A></LI>
     <LI><A HREF="#Routing">Routing</A></LI>
     <LI><A HREF="#Filtering">Filtering</A></LI>
     <LI><A HREF="#Clustering">Clustering</A></LI>
     <LI><A HREF="#Routing">Routing</A></LI>

-    <LI><A HREF="#AvoidingFragmentation">Avoiding Fragmentation</A></LI>

     <LI><A HREF="#Performance">Performance</A></LI>
 </OL>
 
     <LI><A HREF="#Performance">Performance</A></LI>
 </OL>
 


@@ -185,6 +184,11 @@ the same as the LAC, or authentication will fail.  Only actually be
 used if the LAC requests authentication.
 </LI>
 
 used if the LAC requests authentication.
 </LI>
 

+<LI><B>l2tp_mtu</B> (int)<BR>
+MTU of interface for L2TP traffic (default: 1500).  Used to set link
+MRU and adjust TCP MSS.
+</LI>
+

 <LI><B>ppp_restart_time</B> (int)<BR>
 <B>ppp_max_configure</B> (int)<BR>
 <B>ppp_max_failure</B> (int)<BR>
 <LI><B>ppp_restart_time</B> (int)<BR>
 <B>ppp_max_configure</B> (int)<BR>
 <B>ppp_max_failure</B> (int)<BR>


@@ -335,6 +339,10 @@ on <A HREF="#Clustering">Clustering</A> for more information.
 Interface for cluster packets (default: eth0).
 </LI>
 
 Interface for cluster packets (default: eth0).
 </LI>
 

+<LI><B>cluster_mcast_ttl</B> (int)<BR>
+TTL for multicast packets (default: 1).
+</LI>
+

 <LI><B>cluster_hb_interval</B> (int)<BR>
 Interval in tenths of a second between cluster heartbeat/pings.
 </LI>
 <LI><B>cluster_hb_interval</B> (int)<BR>
 Interval in tenths of a second between cluster heartbeat/pings.
 </LI>


@@ -349,8 +357,33 @@ from the master.
 Determines the minumum number of up to date slaves required before the
 master will drop routes (default: 1).
 </LI>
 Determines the minumum number of up to date slaves required before the
 master will drop routes (default: 1).
 </LI>

+
+<LI><B>echo_timeout</B> (int)<BR>
+Time between last packet sent and LCP ECHO generation
+(default: 10 (seconds)).
+</LI>
+
+<LI><B>idle_echo_timeout</B> (int)<BR>
+Drop sessions who have not responded within idle_echo_timeout seconds
+(default: 240 (seconds))
+</LI>
+
+<LI><B>bind_portremotelns</B> (short)<BR>
+Port to bind for the Remote LNS (default: 65432).
+</LI>
+

 </UL>
 
 </UL>
 

+<P>The REMOTES LNS configuration is entered by the command:
+<DL> <DD><B>setforward</B> <I>MASK</I> <I>IP</I> <I>PORT</I> <I>SECRET</I> </DL>
+
+where <I>MASK</I> specifies the mask of users who have forwarded to
+remote LNS (ex: /myISP@company.com).</BR>
+where <I>IP</I> specifies the IP of the  remote LNS (ex: 66.66.66.55).</BR>
+where <I>PORT</I> specifies the L2TP Port of the remote LNS
+(Normally should be 1701) (ex: 1701).</BR>
+where <I>SECRET</I> specifies the secret password the remote LNS (ex: mysecret).</BR>
+

 <P>BGP routing configuration is entered by the command:
 The routing configuration section is entered by the command
 <DL><DD><B>router bgp</B> <I>as</I></DL>
 <P>BGP routing configuration is entered by the command:
 The routing configuration section is entered by the command
 <DL><DD><B>router bgp</B> <I>as</I></DL>


@@ -1050,22 +1083,6 @@ ibgp" for IBGP.  If this is not supported by your IOS revision, you
 can use "maximum-paths" (which works for EBGP) and set
 <B>as_number</B> to a private value such as 64512.<P>
 
 can use "maximum-paths" (which works for EBGP) and set
 <B>as_number</B> to a private value such as 64512.<P>
 

-<H2 ID="AvoidingFragmentation">Avoiding Fragmentation</H2>
-
-Fragmentation of encapsulated return packets to the LAC may be avoided
-for TCP sessions by adding a firewall rule to clamps the MSS on
-outgoing SYN packets.
-
-The following is appropriate for interfaces with a typical MTU of
-1500:
-
-<pre>
-iptables -A FORWARD -i tun+ -o eth0    \
-    -p tcp --tcp-flags SYN,RST SYN     \
-    -m tcpmss --mss 1413:1600          \
-    -j TCPMSS --set-mss 1412
-</pre>
-

 <H2 ID="Performance">Performance</H2>
 
 Performance is great.<P>
 <H2 ID="Performance">Performance</H2>
 
 Performance is great.<P>