.de Id
.ds Dt \\$4 \\$5
..
-.Id $Id: startup-config.5,v 1.1 2004-11-17 15:08:19 bodea Exp $
+.Id $Id: startup-config.5,v 1.7 2005-05-10 11:59:25 bodea Exp $
.TH STARTUP-CONFIG 5 "\*(Dt" L2TPNS "File Formats and Conventions"
.SH NAME
startup\-config \- configuration file for l2tpns
If set, the process id will be written to the specified file. The
value must be an absolute path.
.TP
+.B random_device
+Path to random data source (default
+.BR /dev/urandom ).
+Use "" to use the rand() library function.
+.TP
.B l2tp_secret
The secret used by
.B l2tpns
user, both a primary and a secondary. If either is set to 0.0.0.0, then that
one will not be sent.
.TP
-.B save_state
-When
-.B l2tpns
-receives a STGTERM it will write out its current ip_address_pool,
-session and tunnel tables to disk prior to exiting to be re-loaded at
-startup. The validity of this data is obviously quite short and the
-intent is to allow an sessions to be retained over a software upgrade.
-.TP
.BR primary_radius , " secondary_radius"
Sets the RADIUS servers used for both authentication and accounting.
If the primary server does not respond, then the secondary RADIUS
.B Stop
record when the session is closed.
.TP
+.B radius_interim
+If
+.B radius_accounting
+is on, defines the interval between sending of RADIUS interim
+accounting records (in seconds). Note: checking of this interval
+occurs no more frequently than
+.B cleanup_interval
+seconds (see below).
+.TP
.B radius_secret
Secret to be used in RADIUS packets.
.TP
+.B radius_authtypes
+A comma separated list of supported RADIUS authentication methods
+("pap" or "chap"), in order of preference (default "pap").
+.TP
.B bind_address
When the tun interface is created, it is assigned the address
specified here. If no address is given, 1.1.1.1 is used. Packets
.B send_garp
Determines whether or not to send a gratuitous ARP for the
.B bind_address
-when the server is ready to handle traffic (default: true). This
+when the server is ready to handle traffic (default: true). This
setting is ignored if BGP is configured.
.TP
.B throttle_speed
If set to true, then the current bandwidth utilization will be logged
every second. Even if this is disabled, you can see this information
by running the
-.B
-uptime
+.B uptime
command on the CLI.
.TP
.B cleanup_interval
.B icmp_rate
Maximum number of host unreachable ICMP packets to send per second.
.TP
+.B packet_limit
+Maximum number of packets of downstream traffic to be handled each
+tenth of a second per session. If zero, no limit is applied (default:
+0). Intended as a DoS prevention mechanism and not a general
+throttling control (packets are dropped, not queued).
+.TP
.B cluster_address
Multicast cluster address (default: 239.192.13.13).
.TP
Cluster heartbeat timeout in tenths of a second. A new master will be
elected when this interval has been passed without seeing a heartbeat
from the master.
+.TP
+.B ipv6_prefix
+Enable negotiation of IPv6. This forms the the first 64 bits of the
+client allocated address. The remaining 64 come from the allocated
+IPv4 address and 4 bytes of 0s.
.RE
.SS BGP ROUTING
The routing configuration section is entered by the command
.IR keepalive ,
.I hold
are the timer values in seconds.
+.SS NAMED ACCESS LISTS
+Named access lists may be defined with either of
+.IP
+.BI "ip access\-list standard " name
+.br
+.BI "ip access\-list extended " name
+.PP
+Subsequent lines starting with
+.B permit
+or
+.B deny
+define the body of the access\-list.
+.PP
+.B Standard Access Lists
+.RS 4n
+Standard access lists are defined with:
+.IP
+.RB { permit | deny }
+.IR source " [" dest ]
+.PP
+Where
+.I source
+and
+.I dest
+specify IP matches using one of:
+.IP
+.I address
+.I wildard
+.br
+.B host
+.I address
+.br
+.B any
+.PP
+.I address
+and
+.I wildard
+are in dotted-quad notation, bits in the
+.I wildard
+indicate which address bits in
+.I address
+are relevant to the match (0 = exact match; 1 = don't care).
+.PP
+The shorthand
+.RB ' host
+.IR address '
+is equivalent to
+.RI ' address
+.BR 0.0.0.0 ';
+.RB ' any '
+to
+.RB ' 0.0.0.0
+.BR 255.255.255.255 '.
+.RE
+.PP
+.B Extended Access Lists
+.RS 4n
+Extended access lists are defined with:
+.IP
+.RB { permit | deny }
+.I proto
+.IR source " [" ports "] " dest " [" ports "] [" flags ]
+.PP
+Where
+.I proto
+is one of
+.BR ip ,
+.B tcp
+or
+.BR udp ,
+and
+.I source
+and
+.I dest
+are as described above for standard lists.
+.PP
+For TCP and UDP matches, source and destination may be optionally
+followed by a
+.I ports
+specification:
+.IP
+.RB { eq | neq | gt | lt }
+.I port
+.br
+.B
+range
+.I from to
+.PP
+.I flags
+may be one of:
+.RS
+.HP
+.RB { match\-any | match\-all }
+.RB { + | - }{ fin | syn | rst | psh | ack | urg }
+\&...
+.br
+Match packets with any or all of the tcp flags set
+.RB ( + )
+or clear
+.RB ( - ).
+.HP
+.B established
+.br
+Match "established" TCP connections: packets with
+.B RST
+or
+.B ACK
+set, and
+.B SYN
+clear.
+.HP
+.B fragments
+.br
+Match IP fragments. May not be specified on rules with layer 4
+matches.
+.RE
.SH SEE ALSO
.BR l2tpns (8)
projects / l2tpns.git / blobdiff